PDXTI DT Swiss 350/370 12-15mm TA Conversion

PDXTI DT Swiss 350/370 12-15mm TA Conversion

65.00

PDXTI DT Swiss 350/370 End Caps, combined with the extremely light weight PDXTI 12-15-TA Adapter, allow the use of all DT Swiss Straightpull/Classic MTB ISO , DT Swiss Straightpull/Classic MTB CenterLock, and DT Swiss Straightpull/Classic Road CenterLock front wheel models using DT Swiss 350/370 hubs with a 12mm x 100mm thru axle Road/CX/Gravel fork.
Available as end caps only or with optional 12-15-TA-Adapter. 12mm Thru Axle not included.

CONFIGURATION:
Quantity:
Add To Cart

PDXTI DT Swiss 350/370 end caps, combined with the extremely light weight PDXTI 12-15-TA Adapter, allow the use of several DT Swiss R23 Disc, R24 Disc and 1900 Spline front wheel models utilizing a DT Swiss 350/370 front hub with a 12mm x 100mm thru axle Road/CX/Gravel fork.

A specific known compatibility issue is that 15TA compatible DT Swiss front hubs are available in standard 100mm width in 15mm or QR configurations only, with no existing 12mm end cap available.

The end caps for DT Swiss 15x100mm Thru Axles have an OD of 21mm at the fork interface end, which most 12mm forks will not accommodate.

Our DT Swiss 350/370 12mm-Compatible 15mm end caps solve this problem and bring the durability and performance of several DT Swiss wheel models to road, CX, and gravel use.

Available as a complete kit including PDXTI 12-15-TA Adapter, or as end caps only for use with an existing axle adapter.

 
 

DT SWISS 370/350 END CAPS
- DT Swiss Part Number: HWGXXX0004785S.
- Push-in end caps convert DT Swiss 350/370 Straightpull/Classic MTB ISO , DT Swiss 350/370 Straightpull/Classic MTB CenterLock, and DT Swiss 350/370 Straightpull/Classic Road CenterLock front hubs for use with 100x12TA forks.
- Includes end caps and 12-15-TA Adapter
- Fits the following wheels with DT Swiss 350/370 Classic front hubs:

——- X 1700 SPLINE TWO 27.5 and SPLINE TWO 29 front wheels except 110x15TA PS
——- X 1900 SPLINE 27.5 and SPLINE 29 front wheels except 110x15TA PS
——- M 1700 SPLINE TWO 27.5, and SPLINE TWO 29 front wheels except 110x15TA PS
——- M 1900 SPLINE 27.5 and SPLINE 29
——- E 1700 SPLINE TWO 27.5, and SPLINE TWO 29
——- E 1900 SPLINE 27.5 and SPLINE 29
——- R23 Disc
——- R24 Disc
——- 1600 DICUT db
——- 1600 SPLINE db
——- 1800 SPLINE db
——- ** not convertible with DICUT Aero hubs

DIRECTIONS:
1) Swap end caps: pull the existing end caps off of the hub axle.
2) Push PDXTI DT Swiss 350/370 end caps caps on to axle.
3) Slide 12-15-TA Adapter into the 15mm hub.
4) Install wheel into fork as normal.
5) Install 12mm thru axle as normal.

NOTES: 
- If the existing end caps do not “pop” off the axle easily the end cap O-ring may be dry and sticking. Put a few drops of TriFlow or similar lubricant around the edge of the end caps while turning and allow time for lubricant to reach O-ring. It may also be helpful to insert a 15TA axle or adapter to leverage the cap.

- A thin layer of grease on the O-rings inside the new PDXTI end caps is recommended.

- A thin layer of high quality grease on the outside of the adapter and the outside of the 12mm thru axle are recommended for ease of assembly and to provide an extra moisture barrier.

- Compatible with all 12mm x 100mm forks.

- Compatible with all DT Swiss Straightpull/Classic MTB ISO and DT Swiss Straightpull/Classic MTB CenterLock and DT Swiss Straightpull/Classic Road CenterLock 350/370 front hubs.

- Please note that the critical hub dimension for 12TA fork interfaces is the OD of the end cap, which must be 19mm or smaller. Stock DT Swiss 240 MTB 15TA end caps are 20-21mm and will not fit most 12TA forks.

- Thru axles provide compression of the fork ends where the hub end caps interface with the fork ends. Because all hubs and forks are manufactured by third parties to differing tolerances, to ensure an interference-free fit with all possible combinations the length of the PDXTI 12-15-TA Adapter is just under 100mm.